Chaos Casting! | Alumilite Clear Slow | Live Stream 7.21.2020

Last night, I cast some chaos cutoffs I purchased from RJBWoodTurner when he had his chaos blank sale. I had a lot of fun with this live stream as it was fun to cast the blanks and the audience interaction was good throughout the show. I have learned that good live streams are born from good audience interaction. I haven’t quite figured out how to consistently get good interaction, but I’m working on it. I have had good interaction during resin casting live streams and pen turning live streams, but I’ve also had relative silence and very little participation during some of those same types of live streams.

Last Week’s Project: Last week I turned my first Leveche fountain pen. This was a fun turn and while there were a lot of pieces to the kit, it wasn’t difficult to assemble since I organized the part and laid them out according to the diagram on the instructions. I had a small issue placing the clip, but with a punch, I was able to loosen the cap finial and set the clip into place. After that, the rest of the assembly went smoothly, even if it took me a minute to make sure I had everything it the correct place and orientation.

This Week: This week I went back to the resin casting bench to cast some chaos cutoffs. Bob from RJBWoodTurner makes amazing chaos blanks out of wood where he glues up various pen blanks, cuts them up, then glues them up again in a different orientation, and continues the process a few times. This creates the “chaos” effect. I purchased a blank from his last sale, but I also purchased a box of the cutoffs that weren’t big enough to be pen blanks. I took those cutoff pieces and cast them in Alumilite clear slow to make worthless wood blanks.

The process for casting Alumilite clear slow is to pour the A and B sides in a 1:1 ratio. I first started by using three cups (for three colors) and I poured 90 grams of the A side into each cup. Then, I added my colors to each cup (Caster’s Choice cobalt blue, lime green, and platinum silver). Once I added the colors, I explained that if more color is used, the blanks will be more solid. If less color is used, the more translucent the blanks will be. It all depends on what effect is trying to be achieved. I then stirred in the color. Once the color was stirred into the A side of the resin, I zeroed out my scale and added 90 grams of the B side (hardener), since Alumilite clear slow is a 1:1 ratio as mentioned above. Once I got the B side added to each of the three cups, I stirred them until they reached about 95 degrees Fahrenheit. This is when good color separation happens, so once the resin got up to temperature, I poured the resin into my HDPE block mold from PTownSubbie. When I finished pouring the resin into the molds, I put them in the pressure pot and let them sit under pressure for the next four hours. I poured more than one block would hold, so I poured the extra in other molds I had ready as overflow molds. The pressure pot allows the bubbles to get shrunk down to a size that the naked eye can’t see and makes for a blank that cures properly.

Here is the result is last night’s live stream. The first blank is alumilite clear slow only, and the rest are chaos cutoff blanks.

These blanks were cast during the live stream on 7.21.2020.

Supporting The Channel: A huge shout out goes to my top tier patrons, Mark and Angi! If you are interested in becoming a patron at any level, you can simply click the link here: Become a Patron!

You can also support the Cross Cut Creations shop in other ways. Participating in live streams and commenting on videos are a great FREE way to support what I do. If a monthly subscription to Patreon isn’t for you, that’s not an issue. There is a donate button on the right hand side of this website if a one time donation is a better option. Another way to support what I do is to buy something from my online store, also found on this website. Finally, a last way to support what I do without spending anything extra is to use my Amazon affiliate links. If you click on an affiliate link (found in the description of YouTube videos AND under the Tools I Use tab on this website), anything you purchase using that link will give me a small commission and add NOTHING to your total. All you pay for is the items you put in your cart and purchase. You don’t even have to buy the tool that you click on.

Thank you to all those who interacted during the live stream. I appreciate all of you and appreciate everyone who watches the replay as well. If you have any questions or comments, feel free to reach out to me and I’ll get back to you. If you want to check out the replay of the live stream, you can watch it below:

Casting With Alumilite Clear Slow | Live Stream 7.7.2020

Last night I cast a few blanks with Alumilite clear slow using Caster’s Choice Mica Powders. In total, I was able to cast three dye-stabilized elm burl blanks, four ring blanks, and a few other resin only blanks. It was a productive casting session and I am pretty excited about the results. If you see any blanks on my website, or social media platforms, feel free to reach out to claim the blanks.

Last Week’s Live Stream: Last week I refinished two pens. One pen was a mini bolt action pen and the other pen was a Zen rollerball. These pens were refinished and look like a million bucks now that they have a proper CA finish on them. I’m proud of how they turned out and am very pleased with the result.

New Tool: I was able to acquire the Ryobi AC 4 volt quick turn screwdriver. This will make screwdriver applications just a bit faster. I can’t wait to put this tool to use. An amazon affiliate link is on this website under the “Tools I Use” tab.

This Week: This week I cast three dye-stabilized elm burl pen blanks and the extra resin went toward other pen blanks and ring blanks. To prep the burls, I put a dab of hot glue on the bottom of each burl piece so they wouldn’t float in the mold. The three colors I used were from Caster’s Choice and they were gold, lime green, and white pearl.

I mixed 90 grams of A and 90 grams of B into each of the three colors. Once the resin got up to about 95-100 degrees Fahrenheit, I poured the three colors into an old sports drink container to give the colors a chance to mix and form a fun pattern. When I got all of the colors poured into one cup, I then poured the resin from the single cup into each of the molds I had ready to go. Because I used Alumilite clear slow, I left the blanks in the pressure pot for four hours so they could properly cure.

These pen and ring blanks were cast during a live stream on 7.7.2020. Caster’s Choice colors were used and the hybrids are made from dye-stabilized elm burl.

Supporting the Channel: Huge shout out to my top tier patrons, Mark and Angi! If you are interested in becoming a patron at any level, you can simply click the link here: Become a Patron!

You can also support the Cross Cut Creations shop in other ways. Participating in live streams and commenting on videos are a great FREE way to support what I do. If a monthly subscription to Patreon isn’t for you, that’s not an issue. There is a donate button on the right hand side of this website if a one time donation is a better option. Another way to support what I do is to buy something from my online store, also found on this website. Finally, a last way to support what I do without spending anything extra is to use my Amazon affiliate links. If you click on an affiliate link (found in the description of YouTube videos AND under the Tools I Use tab on this website), anything you purchase using that link will give me a small commission and add NOTHING to your total. All you pay for is the items you put in your cart and purchase. You don’t even have to buy the tool that you click on.

Thank you to all those who interacted during the live stream. I appreciate all of you and appreciate everyone who watches the replay as well. If you have any questions or comments, feel free to reach out to me and I’ll get back to you. If you want to check out the replay of the live stream, you can watch it below:

Casting With Alumilite Clear Slow | Live Stream 6.9.2020

On last night’s live stream, I decided to cast some Alumilite clear slow. Going into the live stream, I didn’t know exactly what I wanted to cast, so with the help of the audience, I decided to cast some sweet gum pod call/handle blanks. Five* different colors and were used for this cast.

Show and tell: I showed off last week’s casting results. Four bottle stopper blanks with walnut shells and three Alumilite clear slow pen blanks for a total of seven blanks were cast. Additionally, I bought a chaos blank and a box of chaos cutoffs from Bob over at RJBWoodTurner. The chaos blank that I bought will become a pen that will be a giveaway for reaching 1,000 subscribers on YouTube! That video will be out as soon as I can make the pen and edit the video. If you want a chance to win the pen, you must be a subscriber, so if you haven’t subscribed to my YouTube channel, be sure to do that. Here’s a link to do that: https://www.youtube.com/channel/UC54fkSR_LBTnG69wcy8G3Gg

Breaking News: The colors used in this live stream were based on baby colors because my wife and I are expecting our first child in October! We are super thrilled and couldn’t be happier. SPOILER ALERT: We can’t wait to meet our DAUGHTER!

I used five colors, but mixed two of them to create a “custom color”, so it ended up being four colors. The four colors were mixes of blues and pinks. I poured 90 grams of A and 90 grams of B since Alumilite clear slow is mixed in a 1:1 ratio. There was a few other partial blanks, but here is a picture of the result of last night’s cast:

These sweet gum pod blanks were cast on a live stream on YouTube. They measure 1.5″ square and 6″ long.

Patreon Support: Thank you to my patrons, Mark & Angi! I really appreciate the support! If you would like to support what I do on YouTube, here is a link to Patreon, but as always, no pressure: Become a Patron!

If Patreon isn’t the way you’d like to show support, there are other ways to do that. First, if you’d like to make a one time donation, there is a link on the right hand column to donate. The next option, in my store on my website, making a purchase of any kind (logo gear or handmade products/projects) are a good way to support what I do, but an even better way to support what I do without spending anything extra, is to use the Amazon affiliate links I have. I get a small percentage of whatever you buy using those links, even if you don’t buy the linked tool/product. You can find the affiliate links in two places. Either use the Amazon links under the “Tools I Use” section on my website, or use the links in the description of my YouTube videos. Finally, an awesome FREE option to support me is to subscribe to my YouTube channel and participate in the chat during the live streams I do.

If you want to check out the replay of the live stream, you  can check it out here:

Thank you for checking out this post and taking the time to read this. It means the world to me that you chose to spend some of your time reading my recap of last night’s live stream. I really do appreciate the support you give me at any level. If all I ever saw was some community engagement, that’s what makes me happy. Until next week, I’ll see you on the next live stream.

Casting Alumilite Clear Slow Pen Blanks | Live Stream 5.26.2020 Recap

On last night’s live stream, I cast Alumilite clear slow resin with Caster’s Choice Mica Powders (Blood Red, Lime Green, & Cobalt Blue). I was able to produce 2 ring blank blocks, 2 regular pen blanks, and 4 bespoke blanks. This resin pour was a lot of fun and I’d like to share the results here:

When pouring resin and doing a color cast, I like to add my color after I pour the A side of the resin. After the resin (A & B mixed) gets up to temperature, that’s when I like to pour into the mold from PTownSubbie. With Alumilite clear slow, for good color separation, I like to pour my resin between 95-100 degrees. Additionally, I like a solid color pen blank (not translucent), so the way I check for that is by using the popsicle stick. If I can see the grain of the popsicle stick, I get a translucent look. If the color completely covers the grain, I know my blank will be have more of a solid color.

I still have to cut up and trim the ring blanks and regular pen blanks, but I’m pretty happy with the outcome. If there’s any interest in these, or any of my blanks, feel free to contact me and let me know what you’d like.

Here’s the live stream video here if you’re interested:

Finally, I forgot to mention that I got my VERY FIRST patron! I want to give a special shout out to Mark for being my very first patron. If you’re interested in becoming a patron at any level, here’s the link, but no pressure.

Become a Patron!

Thanks for checking out my live stream. Feel free to email me with any question, comments, or suggestions!